0.25mm Gas Liquid Separation Demister Pads
Wire mesh Demister Pad
The Gas Liquid Separation Demister Pads increases the purification ratio, that enables a deep cut in residue oil to improve the quality of gas oil. The improved gas oil contains less carbon, asphalt and corrosive metals, increases decomposition capacity by the residue load in the regenerator, and maintains a higher contact reaction to produce a higher gasoline yield ratio.
Feature
Simple structure and light weight
High-quality stainless steel is selected, and the welding is firm
Large contact area, high foam removal efficiency
Easy installation, operation and maintenance, long service life
Wire Mesh Demister Standard Specification (part):
|
Product Name
|
wire mesh demister filter/demister pad/knitted wire mesh demister pad
|
|
Material
|
stainless steel, Monel, nickel ,titanium, PP, PVC, PE, PTFE and so on.
|
|
Wire Diameter
|
0.11mm 0.13mm,0.2 mm, 0.22 mm, 0.23 mm, 0.25 mm, 0.28 mm, 0.3 mm, 0.35 mm.
|
|
Mesh Size
|
2 mm × 3 mm, 4 mm × 6 mm to 12 mm × 6 mm
|
|
Type
|
Common type, compressed type
|
|
Usage
|
Petroleum, chemical, pharmaceutical, environmental protection, gas washing, etc.
|
Wire Mesh Demister Styles:
|
Style
|
Material
|
Density
lb/ft3 (kg/m3)
|
Wire Diameter
Inches (mm)
|
|
A
|
Metallic
|
9 (144.2)
|
0.011 (0.28)
|
|
B
|
Metallic
|
5 (80.1)
|
0.011 (0.28)
|
|
C
|
Metallic
|
12 (192.2)
|
0.011 (0.28)
|
|
D
|
Polytetrafluroethylene(PTFE)
|
normal
|
0.012 (0.30)
|
|
F
|
Polypropylene
|
normal
|
0.012 (0.30)
|
|
G
|
Metallic
|
Variable5 (80.1) - 9 (144.2)
|
0.011 (0.28)
|
|
V
|
Metallic
|
Other
|
normal
|
Where is the application of Wire Mesh DEMISTER ?
Knockout drums and separators – save on capital costs by decreasing vessel size-recover costly fatty acids from stream-reduce compressor maintenance by preventing scale build-up.
Absorbers – reduce overhead losses of glycols in dehydrators to no more than 0.1 gal/MMSCF natural gas-cut losses of absorption oil and amines in CO2 systems.
Scrubbers – reduce chemical discharges from Kraft mill smelt dissolver tank to less than 0.11 kg/dry ton (0.25 lb/dry ton) of pulp-improve scrubber efficiency by removing particulates carried in entrained liquids.
Distillation columns – improve product purities and increase throughput capacities for petrochemicals, organic intermediates, fine chemicals.
Evaporators – prevent carryover loss of valuable products, keep condensate TDS <10 ppm for highest quality boiler feed water-clean up vacuum ejector stream discharge-lower maintenance in vapor re-compression systems.
High pressure steam systems – provide dry steam- cut TDS to <10 ppb in condensate-eliminate build-up on turbine blades.
Refinery towers – increase throughput capacity-take deeper cuts for greater product yields – prolong catalyst life in downstream cracking and reforming units by reducing carbon and metals in side
draws-use lower grade crudes.
Tks for your reading ,i hope my introduction can help you to make a decision ,any question ,contact me right now !
Your message must be between 20-3,000 characters!
